Bunny Lollipop Covers

Supplies

Both designs-
Cardstock – white, brown or gray (Bunny colors)
Blue cardstock for the eyes
Pink Cardstock
Micro Glue Dots #30118927
Mini Glue dots #30001510 3/16”
Meriken Double Stick Tape #30013283
Black Extra Fine tip marker (Pigma Micron ink)
Standard Oval Punch (Clever Lever Orange) #30028696
2 ” Oval Punch (Cleve Lever Pink) #30028753
Giga Shipping Tag Punch (Clever Lever Purple) #30028768
” Hole Punch (Fiskars) #77178558
Sharp Scissors
Ruler and pencil
Lollipops
Optional: Stamps with Easter or Spring Sentiments and ink
Optional: 4” of ribbon

Bunny Head –
3” Oval Punch (Clever Lever Purple) #30028763
1” Circle (Clever Lever Green) #30028718
Standard Heart Punch (Clever Lever Orange) #30028682

Bunny Butt-
2” Circle Punch (Clever Lever Blue) #30028735
1 ” Circle Punch (Clever Lever Yellow) #30028731
2” Oval Punch (Clever Lever Blue) #30028743
” White Pom Pom #30006969

 

 

Directions

To make the Bunny Head –
Punch a 2” Oval out of white or gray cardstock for the head. Punch out two 1” circles from white cardstock. Place in the center of the head for the “cheeks” and adhere with glue dots. Punch a small heart from the pink cardstock. Place in the center of the cheeks and adhere for the nose. Use the extra fine black marker and draw in a few whiskers on either side of the cheeks.
Take the standard oval punch and punch out two from white cardstock and two form blue cardstock. Take the ” hole punch and punch out a circle in each of the white ovals. Place the blue ovals behind and adhere together for the eyes. Use the extra fine black marker to make a small dot in each eye. Place the eye above the cheeks and adhere with glue dots.
For the ears, punch out one 3” oval from matching cardstock. With the oval upright, take the ruler and measure in from the outer edge, ” from each side at the widest point. Mark with the pencil. Take the 3” oval punch again and align at the ” mark and punch. You will get two slim ovals for the ears. Place at the top of the head and adhere to the back.
Take the shipping tag punch and punch out a tag. Use the ” hole punch and make a hole at the pointed end of the tag.
Optional: Stamp a message along the side of the tag or near the bottom (pointed end). Place the lollipop behind the tag, slipping the stick through the ” hole. Adhere the lollipop to the tag with a small piece of tape. Place the bunny head onto the tag and adhere.
Optional: Tie a small piece of ribbon onto the stick below the tag.
 

To make the Bunny Butt –
From the white cardstock, punch out a 1 ” and 2” circle. Slightly overlap the 2” circle on top of the 1 ” and adhere together to make the body and head.
Trace and cut out two (2) feet from white cardstock according to the pattern. Punch out two (2) pink ovals using the Standard Oval Punch. Punch out six (6) ” circles from the pink cardstock. Place one (1) pink oval and three (3) pink circles onto the white oval foot for the foot pads. Adhere with micro glue dots. Place the two feet at the bottom of the body and adhere. Refer to the pictured sample for placement.
Take the 2 ” Oval punch and punch out one oval from white cardstock. Use the ruler to measure in ” from the edge at the widest point. Take the 2” oval punch and align it at that point and punch out two slim ovals for the ears. Place the ears on top of the head and adhere. Refer to the pictured sample for placement.
Place the white pom pom above the feet on the body. Adhere with a glue dot.
Take the shipping tag punch and punch out a tag. Use the ” hole punch and make a hole at the pointed end of the tag. Optional: Stamp a message along the side of the tag or near the bottom (pointed end). Place the lollipop behind the tag, slipping the stick through the ” hole. Adhere the lollipop to the tag with a small piece of tape. Place the bunny onto the tag and adhere. Optional: Tie a small piece of ribbon onto the stick below the tag.

 

 

2012 Ben Franklin Crafts, Inc.

 

  printer-friendly version

 

Back Home   Search Category   Search Name   All Projects List